Kuhnt, Markus (2020)
Structural and magnetic characterization of Fe-Si-B-P-Cu alloys.
Technische Universität Darmstadt
doi: 10.25534/tuprints-00011711
Dissertation, Erstveröffentlichung
Kurzbeschreibung (Abstract)
Nanocrystalline Fe-Si-B-P-Cu alloys have attracted a lot of attention due to a high saturation polarization of about 1.8T combined with low coercivity. Low glass-forming ability however hindered large-scale-application. Recently, it has been reported that Fe81.2Co4Si0.5B9.5P4Cu0.8 and (Fe85.2Si0.5B9.5P4Cu0.8)99 C1 combines good magnetic properties with sufficient glass-forming ability. However, reports on Fe-Si-B-P-Cu alloys could not be reproduced by any other group. In this thesis, we have studied the material’s properties of the base alloy Fe85.2Si0.5B9.5P4Cu0.8 based from that investigated the influence of carbonand cobalt addition. Magnetic and mechanical properties as well as electrical resistivity of Fe85.2Si0.5B9.5P4Cu0.8 have been measured in dependence on annealing temperature Ta by using flash-annealing. In agreement with literature we found in the nanocrystalline state, which is formed at about 400 ◦C, a high saturation polarization of about Js = 1.82 T and low coercivity Hc = 4−5 Acm−1. Saturation magnetostriction is as high as λs = 14 ppm, which can be well understood from the relatively low crystalline fraction νcr = 50 %. Mechanical tests reveal a typical behavior for nanocrystalline Fe-based soft magnetic materials. Due to stress relaxation and the reduction of the free volume, the alloy embrittles well before the formation of the nanocrystalline state. Upon nanocrystallization both hardness and Young’s modulus increase, which can be correlated with an increasing volume fraction of the crystalline α-Fe phase. The electrical resistivity was found dropping from about 124 Ωcm in the as-cast state to about 61 Ωcm in the nanocrystalline state, which is much lower than for Fe-Si-B-Nb-Cu alloys. The low electrical resistivity compared to Fe-Si-B-Nb-Cu alloys causes higher eddy current losses and thus rather limits the use of Fe-Si-B-P-Cu alloys to low frequency applications. For studying the influence of cobalt addition, magnetic and electric properties of nanocrystalline Fe85.2CoxSi0.5B9.5P4Cu0.8 (x = 0, 4, 10, 15, 20, 25, 35, 40, 50, 57 at%) have been investigated and were correlated with their structural properties. Co addition doesn’t effect the crystallization temperatures much and a nanocrystalline phase, comprising a bcc phase and a residual amorphous matrix, is formed for all compositions at alloys at about 400 ◦C. In the nanocrystalline state, both coercivity and magnetostriction increase with Co content, from Hc = 4 A m−1 to Hc = 29 A m−1 and from λs = 14 ppm to λs = 55 ppm, respectively. The saturation polarization reaches a maximum of about 1.88 T at 25 at% Co. Electrical resistivity show a distinct maximum of ρel = 68 Ωcm at 10 at% Co. Both, the dependence of magnetic and electric properties, can be understood from the changing composition of the constituent phases. The influence of carbon addition on magnetic and electrical properties was investigated for Fe85.2−xCxSi0.5B9.5P4Cu0.8 for carbon contents up to x = 3 at%. In the as-cast state, the inter-atomic distance of the iron atoms increases, which results in an increased Curie-temperature TC and eventually in an enhanced saturation polarization Js, but also an enhanced saturation magnetostriction λs. In the nanocrystallie state, carbon addition reduces the grain size of the bcc grains and thus coercivity can be lowered from Hc = 4 A m−1 down to Hc = 2 Am−1. On the other hand, a reduced crystalline volume fraction results in slightly lower saturation polarization and increased saturation magnetostriction. However, the lower volume fraction also enhances electrical resistivity up to about 75 Ωcm for x = 3 at%, which might prove useful for high frequency applications.
Typ des Eintrags: | Dissertation | ||||
---|---|---|---|---|---|
Erschienen: | 2020 | ||||
Autor(en): | Kuhnt, Markus | ||||
Art des Eintrags: | Erstveröffentlichung | ||||
Titel: | Structural and magnetic characterization of Fe-Si-B-P-Cu alloys | ||||
Sprache: | Englisch | ||||
Referenten: | Durst, Prof. Dr. Karsten ; Gutfleisch, Prof. Dr. Oliver | ||||
Publikationsjahr: | 2020 | ||||
Ort: | Darmstadt | ||||
Datum der mündlichen Prüfung: | 24 Juni 2019 | ||||
DOI: | 10.25534/tuprints-00011711 | ||||
URL / URN: | https://tuprints.ulb.tu-darmstadt.de/11711 | ||||
Kurzbeschreibung (Abstract): | Nanocrystalline Fe-Si-B-P-Cu alloys have attracted a lot of attention due to a high saturation polarization of about 1.8T combined with low coercivity. Low glass-forming ability however hindered large-scale-application. Recently, it has been reported that Fe81.2Co4Si0.5B9.5P4Cu0.8 and (Fe85.2Si0.5B9.5P4Cu0.8)99 C1 combines good magnetic properties with sufficient glass-forming ability. However, reports on Fe-Si-B-P-Cu alloys could not be reproduced by any other group. In this thesis, we have studied the material’s properties of the base alloy Fe85.2Si0.5B9.5P4Cu0.8 based from that investigated the influence of carbonand cobalt addition. Magnetic and mechanical properties as well as electrical resistivity of Fe85.2Si0.5B9.5P4Cu0.8 have been measured in dependence on annealing temperature Ta by using flash-annealing. In agreement with literature we found in the nanocrystalline state, which is formed at about 400 ◦C, a high saturation polarization of about Js = 1.82 T and low coercivity Hc = 4−5 Acm−1. Saturation magnetostriction is as high as λs = 14 ppm, which can be well understood from the relatively low crystalline fraction νcr = 50 %. Mechanical tests reveal a typical behavior for nanocrystalline Fe-based soft magnetic materials. Due to stress relaxation and the reduction of the free volume, the alloy embrittles well before the formation of the nanocrystalline state. Upon nanocrystallization both hardness and Young’s modulus increase, which can be correlated with an increasing volume fraction of the crystalline α-Fe phase. The electrical resistivity was found dropping from about 124 Ωcm in the as-cast state to about 61 Ωcm in the nanocrystalline state, which is much lower than for Fe-Si-B-Nb-Cu alloys. The low electrical resistivity compared to Fe-Si-B-Nb-Cu alloys causes higher eddy current losses and thus rather limits the use of Fe-Si-B-P-Cu alloys to low frequency applications. For studying the influence of cobalt addition, magnetic and electric properties of nanocrystalline Fe85.2CoxSi0.5B9.5P4Cu0.8 (x = 0, 4, 10, 15, 20, 25, 35, 40, 50, 57 at%) have been investigated and were correlated with their structural properties. Co addition doesn’t effect the crystallization temperatures much and a nanocrystalline phase, comprising a bcc phase and a residual amorphous matrix, is formed for all compositions at alloys at about 400 ◦C. In the nanocrystalline state, both coercivity and magnetostriction increase with Co content, from Hc = 4 A m−1 to Hc = 29 A m−1 and from λs = 14 ppm to λs = 55 ppm, respectively. The saturation polarization reaches a maximum of about 1.88 T at 25 at% Co. Electrical resistivity show a distinct maximum of ρel = 68 Ωcm at 10 at% Co. Both, the dependence of magnetic and electric properties, can be understood from the changing composition of the constituent phases. The influence of carbon addition on magnetic and electrical properties was investigated for Fe85.2−xCxSi0.5B9.5P4Cu0.8 for carbon contents up to x = 3 at%. In the as-cast state, the inter-atomic distance of the iron atoms increases, which results in an increased Curie-temperature TC and eventually in an enhanced saturation polarization Js, but also an enhanced saturation magnetostriction λs. In the nanocrystallie state, carbon addition reduces the grain size of the bcc grains and thus coercivity can be lowered from Hc = 4 A m−1 down to Hc = 2 Am−1. On the other hand, a reduced crystalline volume fraction results in slightly lower saturation polarization and increased saturation magnetostriction. However, the lower volume fraction also enhances electrical resistivity up to about 75 Ωcm for x = 3 at%, which might prove useful for high frequency applications. |
||||
Alternatives oder übersetztes Abstract: |
|
||||
URN: | urn:nbn:de:tuda-tuprints-117118 | ||||
Sachgruppe der Dewey Dezimalklassifikatin (DDC): | 500 Naturwissenschaften und Mathematik > 530 Physik | ||||
Fachbereich(e)/-gebiet(e): | 11 Fachbereich Material- und Geowissenschaften 11 Fachbereich Material- und Geowissenschaften > Materialwissenschaft 11 Fachbereich Material- und Geowissenschaften > Materialwissenschaft > Fachgebiet Physikalische Metallkunde |
||||
Hinterlegungsdatum: | 10 Jun 2020 12:49 | ||||
Letzte Änderung: | 15 Jun 2020 05:19 | ||||
PPN: | |||||
Referenten: | Durst, Prof. Dr. Karsten ; Gutfleisch, Prof. Dr. Oliver | ||||
Datum der mündlichen Prüfung / Verteidigung / mdl. Prüfung: | 24 Juni 2019 | ||||
Export: | |||||
Suche nach Titel in: | TUfind oder in Google |
![]() |
Frage zum Eintrag |
Optionen (nur für Redakteure)
![]() |
Redaktionelle Details anzeigen |